Training / Certifications / CompTIA Network+ / Transceivers and Connectors

CompTIA Network+ (N10-009) · Lesson 10

Transceivers and Connectors

Explain what a transceiver does, compare the SFP and QSFP form factors and Ethernet vs. Fibre Channel optics, and identify the SC, LC, ST, MPO, RJ11, RJ45, F-type and BNC connectors by shape and use.

Domain 1.0: Networking Concepts (23%)Objective 1.5About 5:48CaptionsStatic view for reduced motion
Lesson 10: Transceivers and connectors Illustrative example: names and values are samples Transceivers andconnectorsModules turn signalsinto light or copper;connectors join thecable to the port.Fiber connectorsCopper connectorsSCpush-pullLCsmall, latchSTtwist-lockMPO12 fibersRJ11phone lineRJ45EthernetF-typescrew-onBNCbayonetTransceiversSFP and QSFP modulesEthernet or Fibre ChannelConnectorsFiber: SC, LC, ST, MPOCopper: RJ11, RJ45, F, BNCComing nextLesson 11: topologiesand architecturesObjective 1.5: Compare and contrast transmission media and transceiversCore switchSFP+ opticWarehouseswitchTransmit: light out on one fiberReceive: light in on the otherelectricalconvertsTransmits and receives: two fibersHot-swappable: no power-downChoose the optic per linkShort reach, long reach or copperForm factorSpeedLanesNotesSFP1 Gbps1Gigabit uplinks; fiber or RJ45 copperSFP+10 Gbps1Same size as SFP; servers and uplinksQSFP+40 Gbps4 x 10Wider; can break out to four 10G linksQSFP28100 Gbps4 x 25Data center spine and core linksQ = quad: four lanes inside one moduleEthernetLAN traffic: switches, servers,firewalls and access pointsOptics such as 10GBASE-SRFibre Channel (FC)Storage area network (SAN):servers to disk arraysLossless, low latency16, 32 or 64 Gbps FC opticsBoth ends must match: protocol, speed, wavelength and fiberSCSubscriber connectorSquare, push-pull snap2.5 mm ferrulePatch panels, older opticsLCLocal connectorSmall, with a latch1.25 mm: half of SCOn SFP and SFP+ opticsSTStraight tipRound, bayonet twist2.5 mm ferruleOlder multimode runsSC = square, ST = stick and twist, LC = little connectorMPO: multi-fiber push on4 send4 unused4 receive40GBASE-SR4 on an MPO-12Usually 12 fibers in one plugParallel optics: 40G, 100GSR4: 100 m OM3, 150 m OM4Factory-made trunk cablesOne MPO-12 plug carries as many fibers as six duplex LCsRJ116 positions2 or 4 contactsPhone lines, DSLRJ45 (8P8C)8 positions8 contacts, 4 pairsEthernet twisted pairSame family, different widths: count the contactsEight contacts = Ethernet (RJ45)F-typeThreaded: screws onRG-6 coaxCable modem and TVBNCBayonet Neill–ConcelmanPush on, quarter turnOld 10BASE2 EthernetVideo and test gearThreaded = F-type; push and twist = BNCFrom the ISP to the storage arrayCable modemFirewallCore switchWarehouse switchServerStorage arrayISPCoax, F-typeRJ45RJ45SFP+ LR optic,duplex LC,single-modeDAC(twinax)FC SFP+LCEvery link: the right module, the right plug, the right cableEthernet to the switches; Fibre Channel to the storageIf the question says……think“Square fiber connector, push-pull”SC“Small fiber connector on an SFP”LC (duplex)“Round fiber connector, bayonet twist”ST“12 fibers in one connector”MPO“Eight-contact Ethernet plug”RJ45“Analog phone line or DSL”RJ11“Threaded coax on a cable modem”F-type“40 or 100 Gbps in one switch port”QSFP“Optics for a storage area network”Fibre ChannelTransceiversSFP 1G, SFP+ 10GQSFP: 4 lanes, 40/100GHot-swappableEthernet or Fibre ChannelFiber connectorsSC: square, push-pullLC: small, on SFPsST: round, twistMPO: 12 fibersCopper connectorsRJ11: phone, 6 positionsRJ45: Ethernet, 8P8CF-type: threaded coaxBNC: bayonet coaxMatch the module and the plug to the port, the cable and the protocol.

Tip: turn your phone sideways or use full screen for larger labels.

Captions match the narration word for word. Press Space to play or pause and the arrow keys to change scenes.

Learning objective

Explain what a transceiver does, compare the SFP and QSFP form factors and Ethernet vs. Fibre Channel optics, and identify the SC, LC, ST, MPO, RJ11, RJ45, F-type and BNC connectors by shape and use.

Exam mapping

Domain 1.0: Networking Concepts (23%). Objective 1.5 in the official N10-009 exam objectives.

Key takeaways

  • A transceiver converts a device's electrical signals to light (or copper signaling) and back. Pluggable modules are hot-swappable, so each port can get the optic its link needs.
  • SFP carries 1 Gbps and SFP+ (same size) carries 10 Gbps. QSFP is wider and carries four lanes: QSFP+ = 4 x 10G for 40 Gbps, QSFP28 = 4 x 25G for 100 Gbps; a 40G QSFP port can often break out to four 10G links.
  • Transceivers are built for a protocol: Ethernet for LAN traffic, Fibre Channel for storage area networks (lossless, low latency, speeds such as 16/32/64 Gbps). Both ends must match in protocol, speed, wavelength and fiber type.
  • Fiber connectors: SC is square and push-pull (2.5 mm ferrule); ST is round with a bayonet twist (2.5 mm); LC is small with a latch (1.25 mm) and is the duplex connector on SFP/SFP+ optics; MPO holds a row of 12 fibers for parallel optics such as 40GBASE-SR4.
  • Twisted-pair connectors: RJ11 is narrow (6 positions, 2 or 4 contacts) for phone lines and DSL; RJ45 is wider (8P8C) and terminates all four pairs of an Ethernet cable.
  • Coax connectors: F-type screws onto threads (RG-6 cable modems and TV); BNC (Bayonet Neill–Concelman) pushes on and locks with a quarter turn (old 10BASE2 Ethernet, video, test gear).

Exam tips

How the exam asks about this

Questions describe a situation and expect you to recognize the concept behind it.

If the question mentions…Think
Square fiber connector with push-pullSC
Small form factor fiber connector on an SFP+ opticLC (duplex)
Round fiber connector with a bayonet twistST
12 fibers in one connector; 40GBASE-SR4MPO
Eight-pin connector on Ethernet cableRJ45 (8P8C)
Phone line or DSL modemRJ11
Screw-on connector on a cable modemF-type
40 or 100 Gbps transceiver, four lanesQSFP (QSFP+ / QSFP28)
Transceiver for a storage area networkFibre Channel

Common traps

  • SC and ST both use a 2.5 mm ferrule, so tell them apart by shape: SC is square and push-pull, ST is round and twist-locks. LC is the small one with half the ferrule size.
  • RJ11 and RJ45 look alike. RJ11 is narrower, with 6 positions and 2 or 4 contacts for phone lines; Ethernet uses RJ45 with 8 contacts.
  • A Fibre Channel SFP+ can look identical to an Ethernet SFP+, but it is built for a different protocol. Match protocol, speed and fiber type at both ends.
  • F-type and BNC are both coax connectors: F-type is threaded (cable modems, TV), BNC is a bayonet quarter turn (10BASE2, video). Neither is used on fiber.

Practice

Exam-style questions

Answer each one before you open the explanation.

Question 1. A technician needs a fiber patch cable for an SFP+ optic in a switch. Which connector will the cable MOST likely need?

  1. ST
  2. SC
  3. Duplex LC
  4. BNC
Show answer

C. Duplex LC. SFP and SFP+ optics use the small duplex LC connector, whose 1.25 mm ferrule fits the module's narrow front. SC is tempting because it's also a common fiber connector, but its 2.5 mm square body is too large for an SFP. ST is an older round twist-lock connector, and BNC is a coax connector.

Question 2. A network engineer needs 40 Gbps in a single switch port, delivered as four 10 Gbps lanes. Which transceiver form factor fits?

  1. QSFP+
  2. SFP
  3. SFP+
  4. RJ45
Show answer

A. QSFP+. QSFP+ is the quad form factor: four 10 Gbps lanes for 40 Gbps, and it can often break out to four 10G links. SFP+ is tempting because it carries 10 Gbps, but only one lane. SFP carries 1 Gbps, and RJ45 is a connector, not a transceiver form factor.

Question 3. Which TWO statements about coaxial cable connectors are correct? (Select TWO.)

  1. F-type connectors screw onto threads
  2. BNC connectors use eight contacts
  3. RJ11 connectors terminate RG-6 cable
  4. BNC connectors lock with a bayonet quarter turn
  5. F-type connectors are used on fiber patch cables
Show answer

A. F-type connectors screw onto threads and D. BNC connectors lock with a bayonet quarter turn. F-type is the threaded coax connector used on cable modems, and BNC pushes on and locks with a quarter turn. Eight contacts describes RJ45, not BNC. RJ11 is a twisted-pair phone connector, not coax. Neither F-type nor BNC is a fiber connector.

Question 4. A data center administrator must connect servers to a storage array over a lossless, low-latency storage area network. Which transceiver protocol should the administrator choose?

  1. Ethernet 10GBASE-SR
  2. Fibre Channel
  3. DOCSIS
  4. 802.11ax
Show answer

B. Fibre Channel. Fibre Channel is the protocol built for SANs: lossless, low-latency links between servers and storage. Ethernet 10GBASE-SR is tempting because the module looks the same, but it carries standard Ethernet LAN traffic. DOCSIS is for cable modems, and 802.11ax is Wi-Fi 6.

Question 5. A technician installs a 40GBASE-SR4 QSFP+ module that sends on four fibers and receives on four more. Which connector does the fiber trunk MOST likely use?

  1. Duplex LC
  2. ST
  3. F-type
  4. MPO
  5. RJ45
Show answer

D. MPO. Parallel optics such as 40GBASE-SR4 use an MPO-12 connector, which holds a row of 12 fibers in one ferrule. Duplex LC is tempting because it's the common SFP connector, but it carries only two fibers; it's used by single-lane optics and by LR4 modules that combine four wavelengths onto one pair. ST is an older two-fiber connector, and F-type and RJ45 are copper connectors.

Transcript

Lesson transcript

The full narration, scene by scene. The captions file contains the same text with timings.

Scene 1 · 0:00

Lesson 10: transceivers and connectors. Welcome to lesson ten, which finishes objective 1.5. Last time we compared the media themselves: copper, fiber, coax and radio. Today we look at what sits at each end. Transceivers are the plug-in modules that turn a switch's electrical signals into light, or send them onto copper. Connectors are the plugs that join a cable to a port. We'll cover SFP and QSFP, Ethernet versus Fibre Channel, and eight connector types.

Scene 2 · 0:31

What a transceiver does. A transceiver transmits and receives. Inside the store's core switch, data is electrical. Plug an SFP+ optic into an empty port, and it turns those signals into laser light on one fiber, and turns incoming light on the other fiber back into electrical signals. The modules are hot-swappable, so you can add or replace one without powering down. That lets one switch serve short links, long links or copper, port by port.

Scene 3 · 1:02

Form factors: SFP and QSFP. Form factor means size and shape. The small form-factor pluggable, or SFP, carries one gigabit, over fiber or even RJ45 copper. SFP+ is the same size but carries ten gigabits. The quad SFP, or QSFP, is wider and packs four lanes into one module. QSFP+ runs four lanes of ten for 40 gigabits, and QSFP28 runs four lanes of 25 for 100. A 40 gig QSFP port can often break out into four 10 gig links.

Scene 4 · 1:35

Protocol: Ethernet vs. Fibre Channel. Transceivers are also built for a protocol. Most carry Ethernet, the LAN traffic between the store's switches, servers and firewall. Fibre Channel is a separate protocol for storage area networks, or SANs, linking servers to disk arrays with low delay and no dropped frames. Fibre Channel optics look like Ethernet SFP+ modules, but run at their own speeds, such as 16, 32 and 64 gigabits. Both ends must match: protocol, speed, wavelength and fiber type.

Scene 5 · 2:08

Fiber connectors: SC, LC and ST. Now the connectors, starting with fiber. The subscriber connector, SC, is square and snaps in with a push-pull motion. The straight tip, ST, is round and locks with a bayonet twist; you'll find it on older multimode runs. Both use a 2.5 millimeter ferrule. The local connector, LC, is the small one: its 1.25 millimeter ferrule is half the size, and it latches like a network plug. Duplex LC is what SFP and SFP+ optics use.

Scene 6 · 2:40

MPO: many fibers, one plug. Multi-fiber push on, or MPO, puts a whole row of fibers in one ferrule, usually twelve. That's how parallel optics work. A 40GBASE-SR4 QSFP module sends on four fibers and receives on four more, through one MPO-12 connector, reaching 100 meters on OM3 or 150 on OM4. Data centers also use MPO trunk cables, made and tested at the factory, so one plug carries as many fibers as six duplex LC connectors.

Scene 7 · 3:12

RJ11 vs. RJ45. On twisted-pair copper, the registered jack connectors look alike, so compare their size. RJ11 is the narrow one: six positions, usually wired with two or four contacts, for analog phone lines and DSL modems. RJ45 is wider, with eight positions and eight contacts, often called 8P8C. It terminates all four pairs in an Ethernet cable, from the store's Cat 6 patch cables to its wall jacks. If you count eight contacts, think Ethernet.

Scene 8 · 3:44

Coax connectors: F-type and BNC. Coax has two connectors to know. The F-type screws onto threads and holds the center conductor of RG-6 cable. You'll find it on the store's cable modem and on TV outlets. The Bayonet Neill–Concelman, or BNC, connector pushes on and locks with a quarter turn. It appeared on old 10BASE2 Ethernet networks, and it's still used for video and test equipment. Threaded means F-type; push and twist means BNC.

Scene 9 · 4:14

The store's rack, connector by connector. Here's the store's network, connector by connector. The ISP's coax ends in an F-type connector on the cable modem. Cat 6 patch cables with RJ45 plugs link the modem, the firewall and the core switch. An SFP+ LR optic with duplex LC sends the uplink over single-mode fiber to the warehouse. A DAC cable connects a server in the same rack, and a Fibre Channel SFP+ links that server to the storage array.

Scene 10 · 4:45

How the exam asks about this. Exam questions usually describe a connector or a need. Square and push-pull is SC. Round with a bayonet twist is ST. Small with a latch, on an SFP, is LC. Twelve fibers in one plug is MPO. Eight contacts is RJ45, and a phone line is RJ11. Screw-on coax is F-type, and twist-lock coax is BNC. Forty or 100 gigabits in one port means QSFP. Storage area network optics mean Fibre Channel.

Scene 11 · 5:17

Recap: transceivers and connectors. To recap: a transceiver converts a switch's electrical signals to light or copper and back, and it's hot-swappable. SFP carries one gigabit, SFP+ ten, and QSFP packs four lanes for 40 or 100. The protocol, Ethernet or Fibre Channel, must match at both ends. Fiber ends in SC, LC, ST or MPO; twisted pair in RJ11 or RJ45; coax in F-type or BNC. Next: how all these links come together in network topologies.

Download captions (WebVTT)

Sources and accuracy

Checked against the official CompTIA N10-009 exam objectives and the standards below on October 24, 2026. Diagrams and addresses in the animation are illustrative.

This free course is independent and isn't affiliated with or endorsed by CompTIA. CompTIA and Network+ are trademarks of CompTIA, Inc.

Preparing a team for Network+?

I run hands-on networking and cloud training for teams, built around your own environment and goals.