WEBVTT
Kind: captions
Language: en

1
00:00:00.000 --> 00:00:07.038
Welcome to lesson ten, which finishes objective 1.5. Last time we compared the media themselves:

2
00:00:07.038 --> 00:00:14.297
copper, fiber, coax and radio. Today we look at what sits at each end. Transceivers are the plug-in

3
00:00:14.297 --> 00:00:20.529
modules that turn a switch's electrical signals into light, or send them onto copper.

4
00:00:20.529 --> 00:00:26.321
Connectors are the plugs that join a cable to a port. We'll cover SFP and QSFP,

5
00:00:26.321 --> 00:00:30.500
Ethernet versus Fibre Channel, and eight connector types.

6
00:00:30.900 --> 00:00:37.511
A transceiver transmits and receives. Inside the store's core switch, data is electrical.

7
00:00:37.511 --> 00:00:44.642
Plug an SFP+ optic into an empty port, and it turns those signals into laser light on one fiber,

8
00:00:44.642 --> 00:00:50.064
and turns incoming light on the other fiber back into electrical signals.

9
00:00:50.064 --> 00:00:56.229
The modules are hot-swappable, so you can add or replace one without powering down.

10
00:00:56.229 --> 00:01:01.800
That lets one switch serve short links, long links or copper, port by port.

11
00:01:02.200 --> 00:01:08.335
Form factor means size and shape. The small form-factor pluggable, or SFP,

12
00:01:08.335 --> 00:01:16.626
carries one gigabit, over fiber or even RJ45 copper. SFP+ is the same size but carries ten gigabits.

13
00:01:16.626 --> 00:01:24.419
The quad SFP, or QSFP, is wider and packs four lanes into one module. QSFP+ runs four lanes of

14
00:01:24.419 --> 00:01:32.461
ten for 40 gigabits, and QSFP28 runs four lanes of 25 for 100. A 40 gig QSFP port can often break

15
00:01:32.461 --> 00:01:34.700
out into four 10 gig links.

16
00:01:35.100 --> 00:01:42.218
Transceivers are also built for a protocol. Most carry Ethernet, the LAN traffic between the store's

17
00:01:42.218 --> 00:01:48.979
switches, servers and firewall. Fibre Channel is a separate protocol for storage area networks,

18
00:01:48.979 --> 00:01:54.460
or SANs, linking servers to disk arrays with low delay and no dropped frames.

19
00:01:54.460 --> 00:02:00.296
Fibre Channel optics look like Ethernet SFP+ modules, but run at their own speeds,

20
00:02:00.296 --> 00:02:07.200
such as 16, 32 and 64 gigabits. Both ends must match: protocol, speed, wavelength and fiber type.

21
00:02:07.600 --> 00:02:14.796
Now the connectors, starting with fiber. The subscriber connector, SC, is square and snaps in

22
00:02:14.796 --> 00:02:21.529
with a push-pull motion. The straight tip, ST, is round and locks with a bayonet twist;

23
00:02:21.529 --> 00:02:27.255
you'll find it on older multimode runs. Both use a 2.5 millimeter ferrule.

24
00:02:27.255 --> 00:02:34.064
The local connector, LC, is the small one: its 1.25 millimeter ferrule is half the size,

25
00:02:34.064 --> 00:02:40.100
and it latches like a network plug. Duplex LC is what SFP and SFP+ optics use.

26
00:02:40.500 --> 00:02:46.012
Multi-fiber push on, or MPO, puts a whole row of fibers in one ferrule,

27
00:02:46.012 --> 00:02:53.388
usually twelve. That's how parallel optics work. A 40GBASE-SR4 QSFP module sends on four fibers

28
00:02:53.388 --> 00:03:00.608
and receives on four more, through one MPO-12 connector, reaching 100 meters on OM3 or 150 on

29
00:03:00.608 --> 00:03:06.509
OM4. Data centers also use MPO trunk cables, made and tested at the factory,

30
00:03:06.509 --> 00:03:11.400
so one plug carries as many fibers as six duplex LC connectors.

31
00:03:11.800 --> 00:03:18.278
On twisted-pair copper, the registered jack connectors look alike, so compare their size.

32
00:03:18.278 --> 00:03:24.029
RJ11 is the narrow one: six positions, usually wired with two or four contacts,

33
00:03:24.029 --> 00:03:30.871
for analog phone lines and DSL modems. RJ45 is wider, with eight positions and eight contacts,

34
00:03:30.871 --> 00:03:38.005
often called 8P8C. It terminates all four pairs in an Ethernet cable, from the store's Cat 6 patch

35
00:03:38.005 --> 00:03:43.100
cables to its wall jacks. If you count eight contacts, think Ethernet.

36
00:03:43.500 --> 00:03:50.497
Coax has two connectors to know. The F-type screws onto threads and holds the center conductor

37
00:03:50.497 --> 00:03:56.080
of RG-6 cable. You'll find it on the store's cable modem and on TV outlets.

38
00:03:56.080 --> 00:04:02.556
The Bayonet Neill–Concelman, or BNC, connector pushes on and locks with a quarter turn.

39
00:04:02.556 --> 00:04:09.627
It appeared on old 10BASE2 Ethernet networks, and it's still used for video and test equipment.

40
00:04:09.627 --> 00:04:13.200
Threaded means F-type; push and twist means BNC.

41
00:04:13.600 --> 00:04:20.992
Here's the store's network, connector by connector. The ISP's coax ends in an F-type connector

42
00:04:20.992 --> 00:04:28.542
on the cable modem. Cat 6 patch cables with RJ45 plugs link the modem, the firewall and the core

43
00:04:28.542 --> 00:04:36.171
switch. An SFP+ LR optic with duplex LC sends the uplink over single-mode fiber to the warehouse.

44
00:04:36.171 --> 00:04:43.484
A DAC cable connects a server in the same rack, and a Fibre Channel SFP+ links that server to

45
00:04:43.484 --> 00:04:44.900
the storage array.

46
00:04:45.300 --> 00:04:51.950
Exam questions usually describe a connector or a need. Square and push-pull is SC.

47
00:04:51.950 --> 00:04:57.709
Round with a bayonet twist is ST. Small with a latch, on an SFP, is LC.

48
00:04:57.709 --> 00:05:04.440
Twelve fibers in one plug is MPO. Eight contacts is RJ45, and a phone line is RJ11.

49
00:05:04.440 --> 00:05:12.388
Screw-on coax is F-type, and twist-lock coax is BNC. Forty or 100 gigabits in one port means QSFP.

50
00:05:12.388 --> 00:05:16.200
Storage area network optics mean Fibre Channel.

51
00:05:16.600 --> 00:05:23.685
To recap: a transceiver converts a switch's electrical signals to light or copper and back,

52
00:05:23.685 --> 00:05:31.004
and it's hot-swappable. SFP carries one gigabit, SFP+ ten, and QSFP packs four lanes for 40 or

53
00:05:31.004 --> 00:05:37.856
100. The protocol, Ethernet or Fibre Channel, must match at both ends. Fiber ends in SC,

54
00:05:37.856 --> 00:05:43.540
LC, ST or MPO; twisted pair in RJ11 or RJ45; coax in F-type or BNC. Next:

55
00:05:43.540 --> 00:05:47.900
how all these links come together in network topologies.
