CompTIA Network+ (N10-009) · Lesson 9
Transmission Media: Wireless and Wired
Compare wireless media (802.11, cellular, satellite) with wired media (802.3 copper, single-mode and multimode fiber, DAC twinax and coax), match each to its speed and distance, and know when plenum-rated cable is required.
Tip: turn your phone sideways or use full screen for larger labels.
Captions match the narration word for word. Press Space to play or pause and the arrow keys to change scenes.
Learning objective
Compare wireless media (802.11, cellular, satellite) with wired media (802.3 copper, single-mode and multimode fiber, DAC twinax and coax), match each to its speed and distance, and know when plenum-rated cable is required.
Exam mapping
Domain 1.0: Networking Concepts (23%). Objective 1.5 in the official N10-009 exam objectives.
Key takeaways
- Wi-Fi is IEEE 802.11: a (5 GHz, 54 Mbps), b (2.4 GHz, 11 Mbps), g (2.4 GHz, 54 Mbps), n = Wi-Fi 4 (2.4 and 5 GHz), ac = Wi-Fi 5 (5 GHz only), ax = Wi-Fi 6 (Wi-Fi 6E adds 6 GHz) and be = Wi-Fi 7.
- Cellular (4G LTE, 5G) gives backup or temporary WAN links without cabling. GEO satellites sit about 36,000 km up (about half a second round trip); LEO satellites orbit a few hundred km up with far lower latency.
- Ethernet is IEEE 802.3. In 1000BASE-T, 1000 is Mbps, BASE is baseband and T is twisted pair. Cat 5e: 1 Gbps to 100 m; Cat 6: 10 Gbps to about 55 m; Cat 6a: 10 Gbps to 100 m; Cat 8: 25/40 Gbps to 30 m.
- Single-mode fiber has a tiny core (about 9 µm), uses lasers and reaches kilometers (10GBASE-LR: 10 km). Multimode fiber has a 50 or 62.5 µm core and reaches hundreds of meters (10GBASE-SR: 300 m on OM3, 400 m on OM4).
- DAC is twinax copper with transceivers built into both ends: cheap, short (about 1 to 5 m passive, up to about 10 m active), for links inside a rack. Coax (RG-6) carries cable internet and TV and ends in an F-type connector.
- Plenum-rated cable (CMP) burns slowly with little smoke and is required in air-handling spaces; non-plenum PVC is cheaper but gives off toxic smoke. Riser (CMR) cable runs between floors.
Exam tips
How the exam asks about this
Questions describe a situation and expect you to recognize the concept behind it.
| If the question mentions… | Think |
|---|---|
| Wi-Fi 6 | 802.11ax |
| 5 GHz-only Wi-Fi 5 | 802.11ac |
| Highest latency WAN link | GEO satellite |
| 10 Gbps over copper to 100 meters | Cat 6a |
| Kilometers of fiber, laser light, narrow core | Single-mode fiber |
| Short, low-cost link between a switch and a server in the same rack | DAC (twinax) |
| Cable modem, RG-6, F-type connector | Coaxial cable |
| Cable in a drop ceiling used for return air | Plenum-rated (CMP) |
Common traps
- Cat 6 isn't Cat 6a. Cat 6 only carries 10 Gbps to about 55 meters; for 10 Gbps over the full 100 meters you need Cat 6a.
- Single-mode has the narrower core but the longer reach. Multimode's wider core lets light take many paths, which limits distance.
- Wi-Fi 5 (802.11ac) is 5 GHz only. Wi-Fi 4 (802.11n) and Wi-Fi 6 (802.11ax) use both 2.4 and 5 GHz, and Wi-Fi 6E adds 6 GHz.
- Plenum cable can replace riser or general cable, but not the reverse: riser-rated cable can't run in a plenum.
Practice
Exam-style questions
Answer each one before you open the explanation.
Question 1. A technician must run cable through the space above a drop ceiling that the building uses for return air. Which cable should the technician use?
- Riser-rated (CMR) cable
- Plenum-rated (CMP) cable
- Standard PVC patch cable
- Outdoor direct-burial cable
Show answer
B. Plenum-rated (CMP) cable. Air-handling spaces need plenum-rated cable, which burns slowly and gives off little smoke. Riser cable is tempting because it's fire-rated too, but it's meant for vertical runs between floors, not plenums. Ordinary PVC cable gives off toxic smoke, and direct-burial cable is for underground runs.
Question 2. A company needs a 10 Gbps link between two buildings 8 km apart. Which medium should the network engineer choose?
- Cat 6a twisted pair
- Multimode fiber
- Direct attach copper
- Single-mode fiber
Show answer
D. Single-mode fiber. Single-mode fiber carries laser light along one path and reaches kilometers (10GBASE-LR goes 10 km). Multimode is tempting because it's also fiber, but at 10 Gbps it reaches only a few hundred meters. Cat 6a stops at 100 meters, and DAC covers only a few meters.
Question 3. Which TWO statements about Wi-Fi standards are correct? (Select TWO.)
- Wi-Fi 6 is 802.11ax
- 802.11ac operates in the 2.4 GHz band only
- Wi-Fi 4 is 802.11n
- 802.11b has a maximum data rate of 54 Mbps
- Wi-Fi 5 is 802.11g
Show answer
A. Wi-Fi 6 is 802.11ax and C. Wi-Fi 4 is 802.11n. Wi-Fi 6 is 802.11ax and Wi-Fi 4 is 802.11n. 802.11ac (Wi-Fi 5) is 5 GHz only, not 2.4 GHz. 802.11b tops out at 11 Mbps; 54 Mbps is 802.11a and 802.11g. 802.11g predates the Wi-Fi generation names.
Question 4. A data center team needs low-cost 10 Gbps links from a top-of-rack switch to servers one meter away. Which option fits BEST?
- DAC twinax cables
- Single-mode fiber with LR optics
- RG-59 coaxial cable
- Cat 5e cable
Show answer
A. DAC twinax cables. DAC is twinax copper with the plugs built in, made for short, cheap links inside a rack. Single-mode fiber with LR optics would work but costs far more and is built for kilometers. RG-59 coax isn't used for Ethernet links, and Cat 5e is rated for 1 Gbps.
Question 5. A remote clinic's only connection is a geostationary satellite link. Users complain that video calls lag badly even though bandwidth is adequate. What is the MOST likely cause?
- Electromagnetic interference on the cabling
- Too many Wi-Fi clients on 2.4 GHz
- Propagation delay from the satellite's high orbit
- A duplex mismatch on the router
Show answer
C. Propagation delay from the satellite's high orbit. A GEO satellite sits about 36,000 km up, so every round trip covers that distance four times and takes about half a second. That latency hurts real-time traffic like video calls. Interference and duplex problems cause errors and drops rather than steady delay, and Wi-Fi congestion would affect the local network, not the WAN link.
Transcript
Lesson transcript
The full narration, scene by scene. The captions file contains the same text with timings.
Scene 1 · 0:00
Lesson 9: transmission media. Welcome to lesson nine, which starts objective 1.5. So far we've talked about what travels across a network. Now we look at what it travels through: the transmission media. Wireless media send radio waves: Wi-Fi, cellular and satellite. Wired media send electricity over copper or light through glass. We'll cover copper categories, fiber, DAC, coax and plenum cable. Transceivers and connectors come in lesson ten.
Scene 2 · 0:28
802.11: the Wi-Fi standards. Wi-Fi is the IEEE 802.11 family. The early standards were 802.11a at 5 GHz and 54 Mbps, 802.11b at 2.4 GHz and 11 Mbps, and 802.11g at 2.4 GHz and 54 Mbps. Then came the generation names. Wi-Fi 4 is 802.11n, the first with MIMO, on both bands. Wi-Fi 5 is 802.11ac, 5 GHz only. Wi-Fi 6 is 802.11ax, and Wi-Fi 6E adds 6 GHz. Wi-Fi 7 is 802.11be.
Scene 3 · 0:58
Cellular and satellite. Cellular uses a carrier's 4G LTE or 5G network. A router with a SIM card gives the store a backup internet link, or connects a pop-up site with no cable at all. Satellite reaches places nothing else does. Geostationary, or GEO, satellites sit about 36,000 kilometers up, so a round trip takes about half a second. Low Earth orbit, or LEO, satellites fly a few hundred kilometers up, so delay is much lower.
Scene 4 · 1:30
802.3: Ethernet over copper. Wired Ethernet is IEEE 802.3. Its names follow a pattern: in 1000BASE-T, 1000 is the speed in Mbps, BASE means baseband, and T means twisted pair. Cat 5e carries 1 Gbps up to 100 meters. Cat 6 carries 10 Gbps, but only to about 55 meters. Cat 6a carries 10 Gbps the full 100 meters. Cat 8 reaches 25 or 40 Gbps over just 30 meters, inside data centers.
Scene 5 · 2:00
Single-mode vs. multimode fiber. Fiber carries light, so electrical interference can't touch it. Single-mode fiber has a tiny core, about nine microns, so the laser light takes one path. That keeps the signal clean over long distances: 10GBASE-LR reaches ten kilometers. Multimode fiber has a wider core, 50 or 62.5 microns, so light bounces along many paths, or modes. 10GBASE-SR reaches 300 meters on OM3 and 400 on OM4.
Scene 6 · 2:29
DAC: direct attach copper. Direct attach copper, or DAC, is a twinax copper cable with the transceiver plugs built into both ends. It plugs straight into SFP+ or similar ports, here from the store's top-of-rack switch to a server in the same rack. Passive DAC cables run about one to five meters, and active ones up to about ten. They cost less than optics and fiber, but they come in fixed lengths.
Scene 7 · 2:58
Coaxial cable. Coaxial cable has a copper center conductor, an insulator, a braided metal shield and an outer jacket. The shield keeps interference out. Today you'll see RG-6 bringing cable internet and TV into a building, where a cable modem uses the DOCSIS standard. It ends in a screw-on F-type connector. RG-59 is an older, thinner type for short runs. Coax is also where a cable ISP hands off to the store.
Scene 8 · 3:29
Cable speeds and reach. Here's how the media compare at ten gigabits and above. Each step on this scale is ten times farther. A passive DAC covers a few meters, so it stays inside the rack. Cat 8 copper reaches 30 meters, and Cat 6a reaches 100, enough for one floor. Multimode fiber covers hundreds of meters, across a building. Single-mode fiber reaches kilometers, between buildings or across a campus.
Scene 9 · 3:58
Plenum vs. non-plenum. The space above a drop ceiling is often a plenum: it carries return air for the heating and cooling system. If a cable burns there, smoke spreads through the building. So fire codes such as the NEC require plenum-rated cable, marked CMP, which burns slowly and makes little smoke. Cheaper non-plenum PVC cable gives off toxic smoke. Riser cable, CMR, runs between floors. Plenum cable can go anywhere, but not the other way around.
Scene 10 · 4:30
How the exam asks about this. Exam questions describe a need. Wi-Fi 6 is 802.11ax, and Wi-Fi 5 is 802.11ac. A backup link without new cable is cellular. The highest latency is GEO satellite. Ten gigabits on copper to 100 meters is Cat 6a. Kilometers between buildings means single-mode fiber, while cheaper fiber inside a building is multimode. Short, cheap links in a rack are DAC. Cable internet is coax. Air-handling space means plenum-rated.
Scene 11 · 4:59
Recap: transmission media. To recap: wireless media include 802.11 Wi-Fi, cellular, and satellite, where GEO is far and slow and LEO is closer and faster. On copper, Cat 5e carries a gigabit and Cat 6a ten gigabits, both to 100 meters. DAC twinax links devices in a rack, and coax brings cable internet. Fiber goes farthest, single-mode most of all. Plenum spaces need plenum-rated cable. Next: the transceivers and connectors that plug into all of this.
Sources and accuracy
Checked against the official CompTIA N10-009 exam objectives and the standards below on October 24, 2026. Diagrams and addresses in the animation are illustrative.
- CompTIA Network+ N10-009 exam objectives (objective 1.5)
- Cisco 10GBASE SFP+ Modules data sheet (SR, LR and twinax distances)
- Cisco Wireless RF Reference Guide (Wi-Fi generations and bands)
- IEEE P802.3bq 25G/40GBASE-T Task Force
- NASA: Catalog of Earth Satellite Orbits
This free course is independent and isn't affiliated with or endorsed by CompTIA. CompTIA and Network+ are trademarks of CompTIA, Inc.
Preparing a team for Network+?
I run hands-on networking and cloud training for teams, built around your own environment and goals.